BIG WARNING: Increasing your router to it’s maximum power can reduce it’s life expectancy, cause problems for your neighbours, can be illegal depending on your location and in some cases even has the potential to cause actual dangerous situations since RADAR can share this frequency!
Taking the above warning into consideration, the allowed transmit power depends on your location and any transmit licenses you might have. With many people living in modern houses which are essentially faraday cages not a lot of harm can be done by increasing the power a bit. But due note that this might not be legal in your country so please check how much you are allowed to transmit using this table.
The first thing you need to do is install the Merlin firmware version 374.43_2, newer ones won’t work! You can download the firmware from Merlin’s site: http://asuswrt.lostrealm.ca/download
Secondly, after installing this you will need to connect either through telnet or through ssh. Here you can enter the following commands but don’t blindly enter them! The last few tell you the transmission power and you probably don’t want it to be 500mW, but these are (as far as I know) the maximum supported:
Note that the
#a here is the country,
#a is the “wildcard” country which enabled all channels supported by the hardware.
TxPower are the ones you need to change to set the transmit power and the nvram commit permanently saves these settings to the router. After that the reboot command will apply everything for you.
I should note that this firmware has some issues with a crashing web interface, luckily that’s easily recoverable through ssh. Just enter this command through ssh and it will be up and running again:
I must downgrade the firmware to 374.43_2 ?
I am currently using Merlin 378.55.
I personally haven’t tested it, but that’s what others have reported. Unfortunately the 374.43_2 firmware has a few bugs but once set up correctly it runs just fine. There are just one or two admin pages that make the webserver crash but that’s easily fixable by restarting httpd
Kun jij mij helpen een hoger vermogen in te stellen in mijn Asus ac66u om meer bereik te testen?
does this also work with the asus dsl-ac68u modem router?
I’m not sure what the current status is but you can try: http://whatsyourrouter.com/mybb/showthread.php?tid=86
From what I read over there, DSL doesn’t work yet so not sure if it’s useful beyond it’s routing/AP capabilities
Works on 380.58
Great! I’ll give it a try
FW: Asuswrt-Merlin fork – build 374.43_2-18E1j9527
It does not save settings enterd via Putty, e.g. setting country to #a and commit shows #a for a little while but then switches back (to EU in my case).
Am I doing something wrong?
The “nvram commit” line should store the settings permanently
If your AP router has a higher transmit power than your station it may not do you much good. See https://boundless.aerohive.com/experts/Does-AP-Transmit-Power-Play-A-Role-In-WiFi-Connectivity-Problems.html
Think of two people if a very noisy room … only one has a megaphone. Two-way communication is not possible.
Correct, this is mostly useful for site-to-site accesspoint connections. Beyond that it probably won’t help much
Is there a possibility to see if the wireless 2.4ghz band is enabled via a ssh command? My ac68u doesnt broadcast the 2.4ghz and i think it’s “secretly” disabled somehwere wich cant be seen via the gui
With the iwconfig command you should be able to see all of the wifi transmitters. But I’d suggest resetting the firmware alltogether. If it’s somehow disabled there might be other settings corrupted.
You don’t even write what the commands are. What is the point of this useless post?
Delete your blog.
I did, it appears a recent wordpress upgrade has broken my code highlighting plugin which resulted in invisible code blocks.
Also… rude much?
Just ignore him and keep you good job.
You might share your and I am quite sure amaizing blog (if any…) !
What a useless and rude comment !
Get a life and respect the information provided
i will wait your next information
Hi, do you know if there is a way to know if all the 3 antennas are really working? I have a second hand unit with Merlin and wished to know if all 3 are in shape!
Depending on the firmware it might be possible to select a specific antenna for a specific purpose. I don’t know if any quick way tuo test though
Can I use the same Merlin firmware for my AC58U? If not where can I find it?
I think it doesn’t work anymore. The manufacturers see this exploit and BAM, it doesn’t work on their newer Hardware.
I just bough an ASUS AC86U, but the 5 Ghz channels 149-165 are missing. In the drop down I see only channels 36-48 and some useless DFS channels
terima kasih kawan, berkatmu saya bisa buat aplikasi router dalam dunia hayalan. mantap kawan
great post thanks
very good blog, very useful for the information and the structure of the writing style, I will come back again for more information